This clamp on meter is a combination power analyzer, power quality logger, and clamp meter, and is ideal for monitoring electronic loads.

With the bright color power meter display to analyze the harmonic spectrum, a low-pass filter to remove high frequency noise, and a high EMC immunity design, the Fluke 345 power analyzer is ideal for troubleshooting power quality on switching loads. Additionally, the Hall Effect clamp meter design makes measurement of dc current possible without the need to break the circuit with the power meter. The internal memory of the power analyzer enables long-term power quality logging for analysis of trends or intermittent problems.

More Information

Features

AC/DC current: Clamp-on measurement of ac current up to 1400 A rms and dc current up to 2000 A without breaking the circuit.
Highest safety rating: 600 V CAT IV power analyzer is rated for use at the service entrance.
Accurate in noisy environments: Clamp meter performs even with distorted waveforms present on electronic loads with low-pass filter.
Data logging: Identify intermittent faults by logging any power quality parameter for minutes, or over a month, including harmonics.
Verify batteries: Direct measurement of dc ripple (%) for battery and dc systems.
Troubleshoot harmonics: Analyze and log harmonics digitally or graphically.
Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds.
Easy to use: Easily confirm power meter setup with large backlit color display of waveforms and trends.
3-Phase power: Built in capability for balanced loads.
View graphs and generate reports: Use power analyzer with included Power Log software.

Model

Fluke Model 345 Power Quality Clamp Meter

Specifications

Operating Temperature	0°C to 50°C
Temperature Coefficient of Current	≤ ±0.15% of reading per °C
Temperature Coefficient of Voltage	≤ ±0.15% of reading per °C
Maximum Relative Humidity	3000 meters
Maximum Operating Altitude	2000 meters

Safety Specifications

Safety	IEC 61010-1 600V CAT IV, double or reinforced insulation, pollution degree 2
Protection	IP40; EN60529
Maximum Safe Working Voltages	Current measurement: 600V AC rms or DC between uninsulated conductor and ground
Maximum Safe Working Voltages	Voltage measurement: 600V AC rms or DC between either input terminal and ground, or 825V between energized phase voltages (delta power configuration)
EMC Emission	IEC / EN 61326-1:1997 Class B
EMC Immunity	IEC / EN 61326-1:1997

General Specifications

Display	Color transmissive LCD 320 x 240 pixels (70mm diagonal) with Two level backlight
Jaw Size	Opening: 60mm
Jaw Size	Capacity: 58mm diameter
Power Supply	Six 1.5-volt type 'AA' Alkaline MN 1500 or IEC LR6 batteries
Battery Life	greater than 10 hours (backlight on full)
Battery Life	greater than 12 hours (backlight reduced)
Battery Eliminator (BE345)	110V to 230V AC 50/60Hz; Output 15V DC, 300mA
Dimensions	300mm (L) x 98mm (W) x 52mm (D)
Weight	820g (including batteries)

Ordering Information

Model Name	Description
Fluke 345	Power Quality Clamp Meter Includes: Six type 'AA' Alkaline batteries, Power Log software, Test Leads, Alligator Clips, Test Probes, USB cable International AC Adapter/Battery Eliminator, User's manual, and Soft Carrying Case.

Specifications

Operating Temperature	0°C to 50°C
Temperature Coefficient of Current	≤ ±0.15% of reading per °C
Temperature Coefficient of Voltage	≤ ±0.15% of reading per °C
Maximum Relative Humidity	3000 meters
Maximum Operating Altitude	2000 meters

Safety Specifications

Safety	IEC 61010-1 600V CAT IV, double or reinforced insulation, pollution degree 2
Protection	IP40; EN60529
Maximum Safe Working Voltages	Current measurement: 600V AC rms or DC between uninsulated conductor and ground
Maximum Safe Working Voltages	Voltage measurement: 600V AC rms or DC between either input terminal and ground, or 825V between energized phase voltages (delta power configuration)
EMC Emission	IEC / EN 61326-1:1997 Class B
EMC Immunity	IEC / EN 61326-1:1997

General Specifications

Display	Color transmissive LCD 320 x 240 pixels (70mm diagonal) with Two level backlight
Jaw Size	Opening: 60mm
Jaw Size	Capacity: 58mm diameter
Power Supply	Six 1.5-volt type 'AA' Alkaline MN 1500 or IEC LR6 batteries
Battery Life	greater than 10 hours (backlight on full)
Battery Life	greater than 12 hours (backlight reduced)
Battery Eliminator (BE345)	110V to 230V AC 50/60Hz; Output 15V DC, 300mA
Dimensions	300mm (L) x 98mm (W) x 52mm (D)
Weight	820g (including batteries)

Ordering Information

Model Name	Description
Fluke 345	Power Quality Clamp Meter Includes: Six type 'AA' Alkaline batteries, Power Log software, Test Leads, Alligator Clips, Test Probes, USB cable International AC Adapter/Battery Eliminator, User's manual, and Soft Carrying Case.

Features

AC/DC current: Clamp-on measurement of ac current up to 1400 A rms and dc current up to 2000 A without breaking the circuit.
Highest safety rating: 600 V CAT IV power analyzer is rated for use at the service entrance.
Accurate in noisy environments: Clamp meter performs even with distorted waveforms present on electronic loads with low-pass filter.
Data logging: Identify intermittent faults by logging any power quality parameter for minutes, or over a month, including harmonics.
Verify batteries: Direct measurement of dc ripple (%) for battery and dc systems.
Troubleshoot harmonics: Analyze and log harmonics digitally or graphically.
Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds.
Easy to use: Easily confirm power meter setup with large backlit color display of waveforms and trends.
3-Phase power: Built in capability for balanced loads.
View graphs and generate reports: Use power analyzer with included Power Log software.

Download Brochures

PDF File 1

Fluke 345 Power Quality Clamp Meter